TerminalSettings (gb.term)

This class allows to define the parameters of a terminal stream.

Свойства

BRKINT	Return or set if a BREAK may interrupts the terminal foreground process.
BSDLY	Backspace delay mask.
CLOCAL	Ignore modem control lines.
CMSPAR	Use "stick" (mark/space) parity (supported on certain serial devices).
CRDLY	Carriage return delay mask.
CREAD	Enable receiver.
CRTSCTS	Enable RTS/CTS (hardware) flow control.
CSIZE	Character size mask.
CSTOPB	Set two stop bits, rather than one.
ECHO	Echo input characters.
ECHOCTL	Echo control characters.
ECHOE	If ICANON is also set, the ERASE character erases the preceding input character, and WERASE erases the preceding word.
ECHOK	If ICANON is also set, the KILL character erases the current line.
ECHOKE	If ICANON is also set, KILL is echoed by erasing each character on the line, as specified by ECHOE and ECHOPRT.
ECHONL	If ICANON is also set, echo the NL character even if ECHO is not set.
ECHOPRT	If ICANON and ECHO are also set, characters are printed as they are being erased.
FFDLY	Form feed delay mask.
FLUSHO	Output is being flushed. This flag is toggled by typing the DISCARD character.
HUPCL	Lower modem control lines after last process closes the device (hang up).
ICANON	Enable canonical mode.
ICRNL	Translate carriage return to newline on input (unless IGNCR is set).
IEXTEN	Enable implementation-defined input processing.
IGNBRK	Ignore BREAK condition on input.
IGNCR	Ignore carriage return on input.
IGNPAR	Ignore framing errors and parity errors.
INLCR	Translate NL to CR on input.
INPCK	Enable input parity checking.
ISIG	When any of the characters INTR, QUIT, SUSP, or DSUSP are received, generate the corresponding signal.
ISTRIP	Strip off eighth bit.
IUCLC	Map uppercase characters to lowercase on input.
IUTF8	Input is UTF-8. This allows character-erase to be correctly performed in cooked mode.
IXANY	Typing any character will restart stopped output.
IXOFF	Enable XON/XOFF flow control on input.
IXON	Enable XON/XOFF flow control on output.
InputSpeed	Return or set the terminal input speed.
NLDLY	Newline delay mask.
NOFLSH	Disable flushing the input and output queues when generating signals for the INT, QUIT, and SUSP characters.
OCRNL	Map CR to NL on output.
OFILL	Send fill characters for a delay, rather than using a timed delay.
OLCUC	Map lowercase characters to uppercase on output.
ONLCR	Map NL to CR-NL on output.
ONLRET	Don't output CR.
ONOCR	Don't output CR at column 0.
OPOST	Enable implementation-defined output processing.
OutputSpeed	Return or set the terminal output speed.
PARENB	Enable parity generation on output and parity checking for input.
PARMRK	Return or set if input bytes with parity or framing errors are marked when passed to the program.
PARODD	If set, then parity for input and output is odd; otherwise even parity is used.
PENDIN	All characters in the input queue are reprinted when the next character is read.
TABDLY	Horizontal tab delay mask.
TOSTOP	Send the SIGTTOU signal to the process group of a background process which tries to write to its controlling terminal.
VDISCARD	Toggle start/stop discarding pending output.
VEOF	End-of-file character (EOF).
VEOL	Additional end-of-line character (EOL).
VEOL2	Yet another end-of-line character (EOL2).
VERASE	Erase character (ERASE).
VINTR	Interrupt character (INTR).
VKILL	Kill character (KILL).
VLNEXT	Quotes the next input character, depriving it of a possible special meaning.
VMIN	Minimum number of characters for noncanonical read.
VQUIT	Quit character (QUIT).
VREPRINT	Reprint unread characters (REPRINT).
VSTART	Start character (START).
VSTOP	Stop character (STOP).
VSUSP	Suspend character (SUSP).
VTDLY	Vertical tab delay mask.
VTIME	Timeout in deciseconds for noncanonical read.
VWERASE	Word erase (WERASE).
XCASE	If ICANON is also set, terminal is uppercase only.

Методы

Copy	Returns a copy of the TerminalSettings object.
MakeRaw	Sets the terminal to "raw" mode.